Sewing Outerwear! Burda 8/2017 Jacket

This post is kind of epic...lots of photos!

Blahhhhh. Not the coat. Me. As mentioned in my prior post, I decided on a slow sewing project for a couple of reasons. And I know that 15 days for a piece of outerwear isn't technically a long time...it felt like forever! LOL! But also felt very low-pressure, which was needed.

I purchased this fabric - wool melton - from Fabric Mart last November in the buy the piece section. I spent $21 for 2.25 yards. When I went to NYC, I saw these buttons at  M&J Trimming and decided they were IT! I spent $3.98 per button and bought 7 (1 extra to have on hand) so they cost more than the main fabric! I got my lining from Metro Textiles.

I traced this pattern in a size 42 and did a 1" FBA and ended up lowering the dior dart too much. Sometimes I notice it and it annoys me...sometimes I don't. I'm sure in the long run I won't care. On Burda tops, I normally trace a size 40 shoulder but stayed with the 42 here because, outerwear. I think it fits fine.

The sleeve measured *ok* but then, I have to always consider the intended design ease - I want to keep with the spirit of the pattern. And since I normally need to add to the bicep I decided to muslin the sleeve to decide on the adjustment.

It was okay -- not tight but I didn't want to struggle when wearing a long sleeves or a sweater underneath. I added 1" which ended up being too much. I took 1/2" out (total) from the back seam. You'll also notice that my sleeve dart is super pointy on the muslin. I ended up having to baste the dart until I got it smooth and then I stitched it and removed the basting stitches.

LOVE the back fit!!!

I love the collar and know why they had you interface the upper and under...but this melton is THICK. I should have used a lighter interfacing or only interfaced one side. The under-collar uses the same piece when really, it should be slightly smaller.

Speaking of the collar...the instructions have you attach a collar stand to each collar piece and then sew those together. The stand almost looked like it didn't fit the collar (there's this flat part on the collar) but you just have to mind your markings. On the stand, I marked in the seam allowance and lined it up with the collar...

And ta-da! Unpicking those stitches was NOT fun though.

I adore the in-seam buttonhole and decided to go with bound buttonholes for the other two. For the windows in the facing, I used the 'interfacing method' where you use interfacing instead of organza and when you turn it to the inside you can fuse it in place. I still stitched around it by machine because I'd rather be safe than sorry.

Makes me happy!!

The shoulder seam on the jacket is forward but I'm not sure why. The facing and lining has the shoulder seam in the normal position. Just a design choice??

The sleeves are new to me...some kind of a raglan / set-in hybrid?? It's 2-piece but you have the dart and it didn't need easing. Weird!

I used a raglan shoulder pad from Wawak

This is the only time I'll ever button that upper button! LOL!!! 

The pockets aren't very usable for me :-/  One, I put them too close to the flaps and two, they sit high up on the body. They can't really be lowered though...if I were making this again for some reason I'd just add welt pockets.

The entire time I was sewing the pocket flaps, I knew that the double layer of melton was too much. After getting them done, I knew there was no way they would attach neatly. So I redid the flaps with lining on the interior. I skipped the topstitching in most places on this jacket. I hand stitched the pockets to the jacket.

Kudos to Burda for their wonderful back lining piece. No finagling to ensure you have ease in back!

When I was ready to do the lining, I pinned the vertical seams of the lining and jacket together and my coat was a bit bigger than my lining. Wahhh! I can only assume that I stretched the wool out a bit during sewing/trying on. I was able to shrink it back with steam for the most part but the front of the lining just was NOT meeting the facing at the bottom. And I had already pinked my lining seams so couldn't let them out. I left it for a couple days and said, screw it. I likely won't ever even notice it.

I cut gussets and finished the area. Shrug.

Then I had it repinned, had sewed the sleeve lining to the sleeves already and was ready to sew the hem. OMG...I forgot the shoulder pads! So I had to go in there and insert them. I sat down to tack the pads in and saw this:

SERIOUSLY?!!?

I unpicked the area, resewed it and FINALLY hemmed it. I placed my inseam button and then placed the others by measuring. It was very important that they line up. When I went to button it I realized I didn't leave enough slack on the functioning buttons so I'll need to re-sew them. Wahhhh! :)

But I finished it and I love it!

I've wanted to take photos at this wall since forever. It's the side of the building of the Ace Hardware. They also had a fall display out and a sign welcoming people to take photos!

This coat has been on my to-do list for awhile and I am SO glad I finally got to it! If you're interested in this one, it's the featured pattern and has full instructions and pics.

I have the Style Arc Mindi pattern cut out so that's up next.